| DVM Agent Queue Port |
DVM Agent to Accops MQ communication is done over this port. |
5672 |
DVM Push |
| Show VM Name |
By default, on user logon, HyWorks provides the name of desktop pool to access. But in cases where users should be shown actual VM Name, this flag can be enabled. No functional impact but enabling may reveal actual VM Name to end-users. |
False |
- |
| DVM Agent Queue Username |
DVM Agent to Accops MQ communication is authenticated using this user name |
guest |
DVM Push |
| Concurrent Full Clone |
Number of concurrent full/replica cloning operation per provider. |
3 |
- |
| DVM Agent Queue Password |
DVM Agent to Accops MQ communication is authenticated using this password. |
4C1F5561261EA036E B4F02383F5D7987 |
DVM Push |
| Desktop Agent Timeout |
Desktop Agent synchronous call timeout (in seconds). |
45 |
Interval |
| DVM Agent Queue Name |
DVM Agent pushes messages on Accops MQ into this message queue. |
edc.dvm.heartbeat-queue |
DVM Push |
| DVM Agent Monitor Control |
DVM Agent Monitor checks DVM Agent status after DVM Agent Monitor Interval. Recommended to set value as 'True' |
True |
Control |
| DVM Tools Upgrade Monitor Interval |
DVM Tools Upgrade monitors new software configuration after this Interval (secs).(Minimum value 5 seconds) |
60 |
Control |
| Desktop Poll Mode |
Desktop Poll Mode: 1.Normal Mode, 2. Hybrid Mode. Default value 1 |
1 |
DVM Push |
| DVM Power Management Control |
DVM power checks which DVM needs to turn off and turn on after "DVM Power Management Interval". Recommended to set value as 'True'. |
True |
Control |
| Concurrent Linked Clone |
Number of concurrent linked cloning operation per provider |
5 |
- |
| DVM Agent Monitor Interval |
DVM Agent Monitor checks DVM agent status after this Interval. (secs).(Minimum value 5 seconds) |
15 |
Interval |
| Verify DVM MAC |
If this flag is enabled then DVM Agent will verify all the MAC addresses before updating VMID pushed from controller. |
False |
DVM |
| Refresh Pools DVM Info Interval |
Refresh DVMs information IP address, power status and more. DVMs that are configured in pool information refreshed after this interval (secs).(Minimum value 10 seconds) |
30 |
Interval |
| DVM push provider timeout |
Refresh Desktop details from hypervisor, if last DVM Agent Push time is more than this interval.(Sec.) |
120 |
DVM Push |
| Concurrent Operation |
Number of concurrent desktop power and delete operation per provider. |
10 |
- |
| DVM push agent refresh timeout |
Refresh desktop agent status , if last DVM Agent Push time and Poll time is more than this interval(Sec.) |
120 |
DVM Push |
| DVM Tools Upgrade Monitor Control |
DVM Tools Upgrade monitors new software configuration after DVM Tools Upgrade Monitor Interval. Recommended to set value as 'True' |
True |
Control |
| Sysprep Attempts DVM |
This value governs no of Sysprep attempts on DVM. |
3 |
Retry |
| DVM Agent Queue Hostname |
Host name of VM where Accops MQ is installed. |
localhost |
DVM Push |
| DVM Agent Queue Heartbeat Interval |
DVM Agent pushes heartbeat data to Accops MQ with this heartbeat interval. |
120 |
DVM Push |
| DVMPushRemoval_Interval |
Disables Desktop Agent information push to queue for the VMs that are removed from pool that were configured as hybrid mode enabled. Iteration is initiated after this interval (min).( Minimum value 1 minute ) |
30 |
Interval |
| Concurrent Operation(Hyper-V) |
Number of concurrent desktop delete operation per Hyper-V Connector (Require service restart). |
2 |
|