Release Summary (AHS-HF-5427)

How to install

HySecure 5.4.5427 can be installed using following methods:

For installation on a public cloud, refer to market place images and installation instructions specific to cloud installations.

Use registered account to download hotfix from support.accops.com.

MD5 Checksum of HotFix: b0199f7e69f8980ba386fb6c37d2cdfa

Gateway ISO	Pre-requisites upgrading to v5427	Procedure
Older than 5.2.5230	Upgrade Not supported Not	applicable
5.2.5230	Minimum patch required is HF 6046 Apply required patches on 5.2.5230 first before upgrade to 5.4 can be done. To achieve patch up to HF 6046, following either of these two patch cycles on top of 5.2.5230 1. HF 6026 → HF 6028 → HF 6033 → HF 6042 → HF 6048 → HF 6046 2. HF 5232 → HF 5235 → HF 5236 → HF 6017 → HF 6026 → HF 6028 → HF 6033 → HF 6042 → HF 6048 → HF 6046 Note: It is mandatory to apply MariaDB hotfix (AHS-HF-5230-GU6046) on 5.2 SP1 (5230) before applying upgrade patch 5.4.5427. This hotfix will ensure smooth database related changes while upgrading from 5.2 SP1 (5230) to 5.4.5427.	Apply mentioned patches and then follow Appendix A: Upgrading HySecure Cluster
5.2.5299	No Patches required. Follow mentioned procedure to apply 5427	Appendix A: Upgrading HySecure Cluster
5.3	Upgrade not supported	NA
6.0	Upgrade not supported	NA

Please refer Appendix A: Upgrading HySecure Cluster for procedure to upgrade HySecure cluster gateway.

The section describes the detailed process to apply hotfix on HySecure Cluster having three nodes (Active, Standby and Real Gateway server).

Note

Before upgrading SP1(5230) cluster setup, MariaDB upgrade hotfix( AHS-HF-5230-GU6046) must

be applied on each cluster node

To upgrade HySecure cluster, follow these main steps:

Connect to Real HySecure Cluster node as Security Officer. Make sure to connect using the actual IP address of the Real node and not the virtual IP address.
Log in as Security officer.
Go to Settings > Cluster > Manage and enable maintenance mode.
Go to Settings > Service Config > Gateway State and and change state to Configuration state.
Go to settings > General Settings > Firmware Upgrade and select upgrade file type as Firmware upgrade and upload the HySecure upgrade patch file. It may take 15 minutes or more to upload the patch based on network bandwidth between your PC and Gateway.
Once the upgrade patch file is uploaded and upgrade has started, the message will be displayed on the browser. In some cases, the message may not come on the Management console. Refresh the browser and see if the upgrade has completed.
After the upgrade patch is applied, you will be logged out.
Log in again and go to Settings > General Settings > Upgrade Firmware and click View Logs to check the upgrade patch installation logs.

Connect to Standby HySecure Cluster Manager node as Security Officer. Make sure to connect using the actual IP address of the Standby node and not the virtual IP address.
Log in as Security officer.
Go to Settings > Cluster > Manage and enable maintenance mode.
Go to Settings > Service Config > Gateway State and and change state to Configuration state.
Go to settings > General Settings > Firmware Upgrade and select upgrade file type as Firmware upgrade and upload the HySecure upgrade patch file. It may take 15 minutes or more to upload the patch based on network bandwidth between your PC and Gateway.
Once the upgrade patch file is uploaded and upgrade has started, the message will be displayed on the browser. In some cases, the message may not come on the Management console. Refresh the browser and see if the upgrade has completed.
After the upgrade patch is applied, you will be logged out.
Log in again and go to Settings > General Settings > Upgrade Firmware and click View Logs to check the upgrade patch installation logs.

Connect to Active HySecure Cluster Manager node as Security Officer. Do not connect using Virtual IP Address, use the actual IP of Active node.
Log in as Security officer.
Go to Settings > Cluster > Manage and enable maintenance mode.
Go to Settings > Service Config > Gateway State and and change state to Configuration state.
Go to settings > General Settings > Firmware Upgrade and select upgrade file type as Firmware upgrade and upload the HySecure upgrade patch file. It may take 15 minutes or more to upload the patch based on network bandwidth between your PC and Gateway.
Once the upgrade patch file is uploaded and upgrade has started, the message will be displayed on the browser. In some cases, the message may not come on the Management console. Refresh the browser and see if the upgrade has completed.
After the upgrade patch is applied, you will be logged out.
Log in again and go to Settings > General Settings > Upgrade Firmware and click View Logs to check the upgrade patch installation logs.
Go to Settings > Service Config > Gateway State and and change state to Run state.

Connect to Active HySecure Cluster Manager node as Security Officer. Do not connect using Virtual IP Address, use the actual IP of Active node.
Login as security officer.
Go to Settings > Cluster > Manage and disable maintenance mode.

Connect to Standby HySecure Cluster Manager node as Security Officer. Do not connect using Virtual IP Address, use the actual IP of Standby node.
Login as security officer.
Go to High Availability > HA enable/disable and disable maintenance mode.

Connect to Real HySecure node as Security Officer. Do not connect using Virtual IP Address, use the actual IP of real node.
Login as security officer.
Go to Settings > Cluster > Manage and disable maintenance mode.